Search Results

This paper describes application of sintered silicon nitride to the swirl lower-chamber in order to improve performance of turbocharged diesel engines. Various stress analyses by finite element method and stress measurements have been applied to determine the design specifications for the component, which compromise brittleness of ceramic materials. Material development was conducted to evaluate strength, fracture toughness, and thermal properties for the sintered bodies. Ceramic injection molding has been employed to fabricate components with large quantities in the present work. Quality assurance for the components can be made by reliability evaluation methods as well as non-destructive and stress loading inspections. It is found that the engine performance with ceramic component has been increased in the power out put of 9PS as compared to that of conventional engines.

Periodic regeneration of the diesel particulate trap is essential to maintain the collection efficiency and exhaust gas hack pressure at acceptable levels. The objectives of this study are to describe the phenomenology of ceramic foam filter regeneration process and to present its mathematical model. Further simulation study is carried out to estimate the effects of various factors including fuel additive on the ignition and the filter bed temperature and to investigate conditions of excessive temperature which could result in filter destruction. The model is based on the assumption that the regeneration process is composed of two steps. The first step is the additional heat supply from the external energy source, and the second step is the spontaneous combustion propagation. The results from the analytical model agreed very well with the experimental results.

In comparison with conventional hot forging process, powder forging process has much advantage such as good dimensional accuracy, minimum scattering of weight, etc. In spite of much advantage, the powder forged parts have not been mass-produced except for relatively simple shape parts because of technical and economic problems such as low productivity. Solving these problems, powder forging process was applied to connecting rods which required fatigue strength and minimum scattering of weight, and which were complex in shape. As a result, for the first time in the world, mass-production of powder forged connecting rods was carried out, and its properties are as follows; (1) Sufficient fatigue strength (2) Minimum scattering of weight (3) Good dimensional accuracy

The design requirement for more efficient vehicle moves a compact car toward front wheel drive arrangement, which requires an entire redesign of its power train. Toyota, with systematic approach from its planning stage, has developed a new automatic transmission series including one 3-speed and two 4-speed transmissions. An extensive examination on gear train arrangements enabled the 3-speed light, compact and highly reliable under the arrangement of Simpson gear train, and freewheel shifts with one-way clutches at every shifting. Two different 4th gear packages with freewheel shift are combined with the 3-speed unit to provide the versatility for the 4-speed units in various installations. Besides, these transmissions feature lock-up clutch converter, oil pump of a new tooth profile and two different control systems: hydraulic and electro-hydraulic.

In a two-loudspeaker stereophonic reproduction system of a passenger car, the geometrical configuration of the right and left loudspeakers has the disadvantage of being asymmetrical to the listener. For this system, we have made both theoretical and experimental verifications of the effects of strongly reflected sounds on the sound pressure level difference and phase difference between two ears which determine the location of sound image in a small compartment of a passenger car. On the basis of these verifications, we have developed a new sound localization control system. With this system, acoustical effects such as sound expansion and ambience have been greatly improved in a passenger car. In this system, input signals to the loudspeakers are controlled so that the sound image produced by the loudspeaker nearer to the listeners may acoustically move so as to position itself symmetrically with the other loudspeaker with regard to the listeners.

Recently, programmable controllers have been utilized for new equipment on production lines in the automobile industry. However, operators who must use these devices to carry out various operations face difficulties understanding the different methods for programming, ets. of these devices, and for handling the various types of peripheral equipment. In accordance with the increase in the number of PCs, CAD/CAM systems have become requisite for achieving high efficiency in sequence control design. However, poor PC standards prevent their development. In this paper, the development of PC systems, as well as methods for the elimination of problems with standardization, are described. The methods of standardization concern the methods of transmission between the PC and the peripheral equipment, the construction of peripheral equipment and the structure of data in the ladder diagram.

On diesel vehicles, we frequently experience the phenomenon that low frequency fore and aft vibration of a vehicle, occurs at acceleration, does not decline in amplitude easily and rather increases finally. The phenomenon has recently attracted great concern in driveability problems on diesel vehicles. This phenomenon can not be explained well by the simple torsional vibration model of the powertrain with one node, which has been used so far successfully to analyze low frequency fore and aft vibration of a vehicle. So, we have assumed that the undamped vibration occurs through the interaction of the engine and the powertrain. Taking this interaction into consideration, we have constructed a simulation model, with which the undamped vibration can be simulated accurately. By this simulation model, we have estimated the order of magnitude of the effects of various design parameters affecting the undamped vibration.

Concerning the road load of the vehicle, there are many discussions about how to measure and how to simulate it on the chassis dynamometer. Also many studies have been done in our laboratory to find out the best solution in aspects of logic, instruments, procedure and reliability. Our solution resulted in “Simplified Coastdown Method (SCD)” which is featured by the concept of force-based measurement and setting of chassis dynamometer. This method was proposed to ISO as a candidate for the standard procedure under the support of Society of Automotive Engineers Japan. In this paper, the method is evaluated by comparing with current coastdown method and wheel torque method. From a practical point of view such as easiness of instruments handling, applicability of the facilities, simplicity of installation and procedure, we have come to a conclusion that the SCD method is the most suitable procedure

This paper contains an explanation of a Multiplex Wiring System with Optical Data-Link for cars, which has been installed in the Toyota “Century” since 1982. In this system, a total of 64 signals related to door wiring are transmitted in a multiplex fashion, and the number of wires from the front right-hand door to the interior could be reduced from 46 wires, which were used with conventional wiring techniques, to 10 wires including 2 plastic optical fibers. This system also has various control functions which includes a door-lock control function. In order to give high reliability to this system, we have developed a new optical data-link as well as a new custom micro-computer. And in the automobile industry, such a large scale multiplex wiring system having high reliability is very innovative in our opinion and will surely have a large impact in the future.

TOYOTA MOTOR CORPORATION had developed the world's first microprocessor controlled suspension system, Toyota Electronic Modulated Suspension (TEMS), which is now being offered on the Toyota Soarer from Feb. '83. This system consists of sensors, switches, electronic control unit (ECU), actuators and shock absorbers. TEMS uses a microprocessor to adjust the damping forces of the front and rear shock absorbers. As a result, suspension can be tuned in two stages (hard and soft cushioning) and driver can choose three control modes (AUTO, SPORT, NORMAL). In AUTO mode, the TEMS system has achieved attitude controls (i.e. squat control, roll control and nosedive control). The TEMS system achieved a 15 - 30% decrease of squat, a 20 - 30% decrease of roll angle, a 10 - 30% decrease of nose-dive and a 30 - 40% decrease of shift-squat.

Computer aided systems for performance evaluation of functional devices for passenger cars, such as engines or transmissions, have been applied for ten years. These systems generally consist of a large main frame computer or minicomputers for conducting a large number of complicated analyses. In the past, these computer aided systems were used for vehicle research and development since they were too expensive and sophisticated for use on the production line. Today, microcomputers with mass memory or personal computers are available at very low cost in comparison to conventional minicomputers. With many distributed microcomputers, we have developed a new test and control system for the engine production line. This system consists of (1) a microcomputer with a disk system for test data storage, (2) five personal computers for the man-machine system and data processing, and (3) microcomputers for real time control and data acquistion.

The camshaft for an automobile engine is generally made of chilled cast iron. Due to increasing demand for higher performance, lawer maintenance and better fuel economy, it is difficult to make the cast iron camshaft lighter and/or more durable. In order to overcome these problems, development of an integral camshaft comprised of a sintered alloy cam piece for better wear resistance and steel tube for weight saving has been accomplished. In 1981 Toyota Motor Corporation successively started the mass-production of the sintered intergral camshaft for the new 1.8 liter ls engine. The significant advantages are as follows; (1) Weight saving (2) Excellent wear resistance (3) Improvement of lubrication system (4) Saving machining cost

An analysis system for vehicle noise and vibration has been developed. It consists of minicomputer based analog processing system connected with a large main-frame computer. This system features multi-modes for data analysis, fast data processing, data compatibility with conventional analog systems and feasibility. Fast data processing was achieved by newly developed FFT processor and minicomputer software. A new remote control box makes it simple to operate. Data processed by the minicomputer can be transferred to a large mainframe computer for further analysis.

In order to reduce the interior noise of a vehicle with a four-cylinder engine, investigations were made using finite element and vector methods, acoustic intensity testing and holography technique. The investigation resulted in inclination of the engine mounting, design changes to the front suspension member, a shock absorber engine mounting, structural modifications to reduce body panel vibration and a new engine mounting to insulate high frequency engine vibration.